24 - 240 Volt AC, 50/60 Hz
Torque up to 4 in-oz

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Self-aligning bronze bearings
Non-reversible
Continuous duty
Approximately 3200 N/L rpm @60 Hz Options Leads or terminals
Cooling fan Typical Applications:

• Evaporator fans
• Heat gun blowers

Rotor Shaft:

• Diameter: .125in./3.175mm or .203in./5.1562mm
• Custom length
• Front or rear extension

24 - 240 Volt AC, 50/60 Hz
Torque up to 11 in-oz

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Self-aligning bronze bearings
Non-reversible
Continuous duty
Approximately 3200 N/L rpm @60 Hz Options Leads or terminals
Cooling fan Typical Applications:

• Pump drives
• Air compressor drives
• Evaporator fans
• Humidifier pump drives

Rotor Shaft:

• Diameter: .203in./5.1562mm or .250in./6.350mm
• Custom length
• Front or rear extension

Centrifugal Blower
and Motor Assembly

This compact unit is designed to provide maximum cooling power in minimum space. It is recommended for use in business machines, electronic equipment... wherever air movement is necessary and space is at a premium.

Specifications Motor

• Two pole shaded pole AC, 6 to 240 volts, 50 or 60 Hz
• Self-aligning porous bronze bearings.
• Furnished with solder lugs, leads, and quick disconnect spades.
• Integral mounting bosses on bearing bracket.

Blower

• Rubber-mounted on motor for silent operation.
• Molded plastic housing.
• Housing can be rotated 360° independent of back mounting.

High-Speed
High-Torque Gear Motor

Motor Specifications:

• 2 Pole Shaded Pole
• 1/50hp to 1/20hp
• 12V to 240V 50 and 60 Hz
• Continuous Duty with cooling fan

Gear Reducer:

• Molded Helical Gearing
• Quiet, Long Life
• Rigid construction on 1/4" Steel Rods
• Special End Brackets available for mounting

Recommended for:

• Duplicating Equipment
• Computer Perriphral Equipment
• Business Machines
• Marking Equipment

24 - 240 Volt AC, 50/60 Hz
Torque up to 30 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox, stamped cover
Bronze sleeve bearings
Non-reversible
Custom duty cycles Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears Typical Applications:

• Medical equipment
• Vending machines
• Coffee machine ingredient motors
• Restaurant equipment

Output Shaft:

• Diameter: .187in./4.7498mm,
  .250in./6.350mm or
  .312in./7.9248mm
• Custom length
• Front or rear extension

24 - 240 Volt AC, 50/60 Hz
Torque up to 30 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox, stamped cover
Bronze sleeve bearings
Non-reversible
Custom duty cycles Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears Typical Applications:

• Medical equipment
• Vending machines
• Restaurant equipment

Output Shaft:

• Diameter: .250in./6.350mm or
  .312in./7.9248mm
• Custom length
• Front or rear extension

24 - 240 Volt AC, 50/60 Hz
Torque up to 40 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox, stamped cover
Bronze sleeve bearings
Non-reversible
Custom duty cycles Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears
Die cast cover Typical Applications:

• Medical Equipment
• Vending Machines

Output Shaft:

• Diameter: .250in./6.350mm or
  .312in./7.9248mm
• Custom length
• Front or rear extension

24 - 240 Volt AC, 50/60 Hz
Torque up to 60 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox
Bronze sleeve bearings
Non-reversible
Custom duty cycles Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears Typical Applications:

• Restaurant Equipment
• Ingredient motors

Output Shaft:

• Diameter: .250in./6.350mm or
  .312in./7.9248mm
• Custom length
• Front or rear extension

24 - 240 Volt AC, 50/60 Hz
Torque up to 60 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox, stamped cover
Bronze sleeve bearings
Non-reversible
Custom duty cycles Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears Typical Applications:

• Lottery ticket dispensing machines
• Vending machines
• Gaming equipment

Output Shaft:

• Diameter: .250in./6.350mm,
  .312in./7.9248mm or
  .375in./9.525mm
• Custom length
• Front or rear extension

24 - 240 Volt AC, 50/60 Hz
Torque up to 100 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox
Stamped steel or die cast cover
Bronze sleeve bearings
Non-reversible
Custom duty cycles Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears Typical Applications:

• Restaurant equipment
• Vending machines
• Valve actuators

Output Shaft:

• Diameter: .250in./6.350mm,
  .312in./7.9248mm or
  .375in./9.525mm
• Custom length
• Front or rear extension

24 - 240 Volt AC, 50/60 Hz
Torque up to 30 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox and cover
Bronze sleeve bearings or needle bearings
Non-reversible
Custom duty cycles available Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears Typical Applications:

• Vending machines
• Carousel drives
• Pump drives
• Brewer motors

Output Shaft:

• Diameter: .250in./6.350mm,
  .312in./7.9248mm, .375in./9.525 or
  .500in./12.700mm
• Custom length
• Front or rear extension
• Custom materials

24 - 240 Volt AC, 50/60 Hz
Torque up to 30 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox and cover
Bronze sleeve bearings or needle bearings
Non-reversible
Custom duty cycles available Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears Typical Applications:

• Vending machines
• Carousel drives
• Pump drives
• Brewer motors

Output Shaft:

• Diameter: .250in./6.350mm,
  .312in./7.9248mm, .375in./9.525 or
  .500in./12.700mm
• Custom length
• Front or rear extension
• Custom materials

24 - 240 Volt AC, 50/60 Hz
Torque up to 30 in-lb

Construction Features Shaded pole motor
Impedance or thermally protected
Class B insulation
Die cast gearbox and cover
Bronze sleeve bearings
Non-reversible
Custom duty cycles Options Leads or terminals
Cooling fan
Brake or clutch
Low noise helical gears
Needle bearings Typical Applications:

• Vending machines
• Brewer motors
• Valve actuators
• Ice dispensing mechanisms

Output Shaft:

• Diameter: .312in./7.9248mm or
  .375in./9.525
• Custom length
• Front or rear extension

Centrifugal Pump
and Motor Assembly

This high-performance economical unit is ideally suited for use in liquid electrostatic duplicating machines, humidifiers, advertising displays, office copying machines, photographic developing machines and similar applications.

Specifications Motor

• Two pole shaded pole AC, 6 to 240 volts, 50 or 60 Hz
• Rated at 15 watts, 1/200 HP. Impedence protected. Available high or low speed to meet application's flow requirements.
• Zinc diecast plate for tank mounting.
• Drive shaft column allows pump outlet to function as required in any position in a 360° circle.

Pump

• Column, housing, and self-cleaning impeller of molded Delrin.
• Outlets - standard vertical; single or double horizontal also available.
• Inlet - flooded sump.

Right Angle Drive
Gear Motor

Motor Specifications:

• 2 Pole Shaded Pole AC.
• 6 to 240 volts, 50 or 60 Hz
• Output speed 1/5 to 100 RPM
• Input bearings - self aligning porous bronze with oil reservoir.

Gear Reducer:

• Worm gear drive for exceptionally quiet performance.
• Self-lubricating Delrin gears-under 15 inch pounds.
• Hardened alloy steel and powdered iron gears for higher torque requirements.
• Rugged zinc diecast gear case. Gear bearing shafts are highly polished and hardened for long life.

Optional Features:

• Long Life Bearing Brackets
• Varnished Stator
• Thermal Protection
• Stainless or Plated Shafts
• Cooling Fans
• Solder Terminals or Leads or Quick Disconnect Spades
• Fuse Link